ReleaseNotes_3rdPartyMCAL_VectorIntegrations
3rdParty MCAL Integration
Release Notes
Renesas RH850 P1M-C/P1H-C/P1H-CE
Version 1.0.0
Authors
Andrej Gazvoda
Status
Released
Release Notes 3rdParty MCAL Integration
Document Information
History
Author
Date
Version Remarks
Andrej Gazvoda 2017-07-27 1.0.0
Basic Integration of P1M-C Mcal
Roland Suess
2017-08-09
Update regarding AUTOSAR_RH850_P1M-
C_MCAL_Ver4.02.01.D
Reference Documents
No.
Source
Title
Version
[1] Vector
TechnicalReference_3rdParty-MCAL-Integration.pdf
see delivery
Scope of the Document
This document contains information about the integration of 3rd Party MCAL into Vector
software stack.
© 2017 Vector Informatik GmbH
Version 1.0.0
2
based on template version 6.0.1
Release Notes 3rdParty MCAL Integration
Contents
1
MCAL Integration .......................................................................................................... 4
1.1
Type of Integration ............................................................................................. 4
1.2
MCAL Location within SIP .................................................................................. 4
1.3
Supported 3rd Party Products ............................................................................. 4
1.4
Configuration Tools ............................................................................................ 5
2
Vector Comment ........................................................................................................... 6
2.1
Known Issues .................................................................................................... 6
2.1.1
Spi module cannot be generated........................................................ 6
3
Glossary and Abbreviations ........................................................................................ 7
3.1
Glossary ............................................................................................................ 7
3.2
Abbreviations ..................................................................................................... 7
4
Contact .......................................................................................................................... 8
© 2017 Vector Informatik GmbH
Version 1.0.0
3
based on template version 6.0.1
Release Notes 3rdParty MCAL Integration
1 MCAL Integration
1.1
Type of Integration
Comfort Integration
Vector tool DaVinci Configurator 5 is used for configuration
> as comfort editor for Mcu component (clock tree)
> as generic editor for other MCAL modules
Recommended workflow:
Generation and changes in configuration are done in DaVinci Configurator.
1.2
MCAL Location within SIP
The 3rd Party MCAL is separated from the Vector parts within the SIP. Furthermore, it
might not be part of the delivery. In this case please refer to chapter ‘First Steps’ in
document TechnicalReference_3rdParty-MCAL-Integration.pdf [1].
1.3
Supported 3rd Party Products
This integration supports the following Renesas targets:
RH850P1M-C
Note
Please refer to the Release Notes of the 3rd Party Products for further
information, e.g. regarding supported versions, derivatives and compilers.
Note
Please be aware that only official 3rdParty-Vendor releases are part of this Vector
integration package. Therefore any customer-specific releases cannot be considered.
© 2017 Vector Informatik GmbH
Version 1.0.0
4
based on template version 6.0.1
Release Notes 3rdParty MCAL Integration
Caution
Please contact the 3rdPartyVendor to find out if there are further Hotfixes
available for your Mcal package.
It is essential to replace the affected MCAL parts in your original package
before you start Script_MCAL_Prepare.bat.
1.4
Configuration Tools
> DaVinci Configurator 5
© 2017 Vector Informatik GmbH
Version 1.0.0
5
based on template version 6.0.1
Release Notes 3rdParty MCAL Integration
2 Vector Comment
Please
consider
the
attached
TechnicalReference_3rdParty-MCAL-
Integration.pdf [1] for further information regarding Vector integration and setup of a
project.
2.1
Known Issues
The original MCAL package might contain errors. Necessary patches are provided via the
SIP folder ThirdParty\ Mcal_Rh850P1xC\VectorIntegration\Patches\ (called
'patch folder' in this chapter).
2.1.1
Spi module cannot be generated
The reference destination of the configuration parameter SpiClockFrequencyRef is wrong
in the Spi module description file. Therefore no valid configuration can be created and
generation is not possible. To allow generation the file Copy_SPI_bswmd.arxml in the SIP
folder BSWMD has to be replaced against the corrected file in the patch folder.
This issue has been reported to Renesas issue database with ARCAADA-613.
© 2017 Vector Informatik GmbH
Version 1.0.0
6
based on template version 6.0.1
Release Notes 3rdParty MCAL Integration
3 Glossary and Abbreviations
3.1
Glossary
Term
Description
3rd party components BSW modules not provided by Vector. Vector may have integrated the
/ MCAL
software within the SIP but does not take over any responsibility
regarding functionality of these modules.
DaVinci Configurator Configuration and generation tool for Vector MICROSAR components
Table 3-1 Glossary
3.2
Abbreviations
Abbreviation
Description
MCAL
Microcontroller Abstraction Layer
AUTOSAR
Automotive Open System Architecture
SIP
Software Integration Package (as provided by Vector)
Msn
Module Short Name derived from AUTOSAR
Table 3-2 Abbreviations
© 2017 Vector Informatik GmbH
Version 1.0.0
7
based on template version 6.0.1
Release Notes 3rdParty MCAL Integration
4 Contact
Visit our website for more information on
> News
> Products
> Demo software
> Support
> Training data
> Addresses
www.vector.com
© 2017 Vector Informatik GmbH
Version 1.0.0
8
based on template version 6.0.1